CANON ERROr CODE

FC-770 Reset E0 - close the two pins on the front of the card and turn on the device, the lock comes off.In the left part of the board has two contacts, closes them - will self-test, and you can rebuild the position of the film (as a FS330, there is indication of C, and the film itself comes at the right position).NP 1215 Error E000 samosbrasyvaetsya after at least 5-10 minutes (the time of self-discharge of the capacitor in the circuit board controller) so that the user did not have the ability to quickly perevklyuchit car, especially in the case of a blown thermistor. If the impatient:Turn the powerPress the switch SW301 DC controller board (left, with the lid "stove")Turn off the power and then turn it on again.NP 3525 Error P0 big green reset button under the front door unit.NP 6x12 Resetting E00 * - shoot "face" (without disconnecting the cable) under it on the board (near the round flat battery), carefully closes the contact between a JP103 and JP104, turn on the machine. Off. NC contact.NP 7161Reset and similar errors E00x (E000, E001, E002, E003, E004).Some of the phones in this series E002 (warm-stove) An error in the program ROM.You can remove these machines Mode Standby, forcing them off the network after 10 minutes, and the error is no more. This is done as follows: press "head with an asterisk" User Mode Key (User Mode), amassed 03, click Start, the "+" or "-" choose the value "1", which corresponds to the shutdown of the network after 10 minutes, once you press Start , press "head with a star" - everything.Often after the E002 device shuts down very quickly, must find time to clear the error, what do the following: turn on the unit lights up E002, you press the head with an asterisk, then both 2 and 8 (approximately 0.5 seconds), then again, you press the head with an asterisk on indicator will light up the number of copies [1], have amassed four, push AE key, dial the 12, you press Start, turns 002, you press one more time Start, the machine dies. Turn on the machine, everything is OK.Often the first attempt to enter the service does not work - pressing the button after the copier must be fast enough.Just get rid of the error E002 can be flashing the ROM (available in the "Repair" - "Useful stuff"), but need to do it with skill, otherwise you can get a dead phone.Similarly, you can reset and other errors E00x (eg, E001), only instead of 002 will be 00h, respectively; E000 and E004 reset code 412.PC 850 If, after replacing the cartridge continues to burn "Replace Cartridge", press [A] (Automatic Exposure) not less than 4 seconds, the counter will be copies of "UC". Click [Start]; indication of "UC" will flash for about 20 seconds., After which the unit will go into normal mode.iR12xxiR15xxiR16xx reset E000.If the heater unit is tested and its performance are you sure - enter the service mode: press the User Mode Key "User Mode Key"; then press "#" - appears on the display "# 1 SSSW»; pressing the arrows select # 7 PRINTER, Press «OK»; pressing the arrow, select # 4 PRINTER RESET, press the left arrow (YES) (click for IR1600 «*» (YES)), the machine off and on.If you then lost the Russian language (in the display, the user-mode it will not be in the list) - once again enter the service mode, pressing the arrow, select # 5 TYPE, press «OK»; pressing the arrows select EUROPE2, click «OK» , then the user-mode will be available.Enter the service mode:NP 4050NP 6045Open the front panel and plug into the trailer plug so as not to shut down.On the left is a hole under the panel with a button inside, insert something thin and press the button. The display lights up $ then press *.The menu, press 4 - this is the entrance to the menu SERVICE; press again *.To exit the service click the blue button a few times.NP 6521 Push "OFF" for more than 2 seconds